Materials:
-fabric-Velcro
-Scissors-Needle-Hilo
Instructions:
Take a piece of cloth and cut it out in a rectangle. Sew right sides, left and bottom, leaving a flap on the top to the top of the purse. Paste the Velcro, some up and some down to open and close your pretty purse. You can decorate with pieces of cloth your wallet. You can make different sizes and colors your precious purse. WOOL FLOWERS
flowers enliven every corner of our home, but keeping them can be a bit annoying. So today we tell you how to make these fun, beautiful flowers wool pom pon. They are perfect to decorate a vase or a nice touch to give away.
Materials: Wool
thick branches, wire jewelry, etc. Wire-cutting clamp
Step by step: Start
a few turns of yarn around your fingers. When you remove a few turns the wool in your hand carefully and have a piece of yarn through the middle. Tie the ends of that piece of wool and then carefully cut the wool around the middle.
This will form the pom pon. Emprolíjalo with scissors and make sure it is well rounded. Finally paste the pom pon with the glue gun at the end of a branch or wire of your choice. CAT NOTEBOOK
Materials:
• Notebook • A sheet of light blue rubber eva, eva rubber sheet yellow and black
• Hot glue or contact cement
• Acrylic white, black, green, orange and red.
• Brushes • Scissors • yellow card
Instructions:
HANDS ON:
1 *- eva rubber is glued on the top blue with a pinceleta (I recommend no one takes the white acrylic is loaded brush, clean the role of "kitchen" and passes with quick strokes.
2 *- 2 lines are cut yellow rubber eva stick one on the bottom and one on the left side without being brought together.
3 *- First paint two lines Orange (brush N ° 0) on the rubber eva vertical leaving a space between them, to dry the back of a brush made by small green circles, just load the painting and pressed with the tip of the brush on the rubber eva. With a brush linner or No. 2 are the leaves, still just not very marked ovals. Finally there is the window frame with a brush No. 14 just three lines, one on yellow rubber eva, a vertical and a third cross it. *-
4 eva rubber is cut black design, the figure of the cat and stick on the black line.
5 *- On the inside back cover, place a yellow square with adhesive vinyl stuck on the bottom and right.
6 *- In the back paste a yellow rubber eva box. CREATIVE MASKS
Materials List:
Gauze bandages or plaster, water, paints, brushes, sequins and glitter.
Instructions:
Place several layers of plaster bandages on his face, taking care of the eyes and nose, is molded with the fingertips. Allowed to dry on face for 15 minutes and a couple of hours off, then painted and applied frost, decorate with sequins
DECORATED PAPER Materials List: Paper
comet, tissue paper, glue, water, brush, dried oregano and dried flowers.
Instructions: Spread the role
kite and take a layer of glue diluted with water. Now sprinkle the dried flowers, oregano, etc.. Place tissue paper over and secure bonding, add another layer of glue gently lowered. Dry the hours that are necessary and have your paper ready
0 COMMENTS
decorated with breadcrumbs FIGURES
Materials List:
bread crumbs, a glass of water, acrylic paints and a cardboard circle.
Instructions:
Board bread crumbs and then Pour water droplets and shapes until you find a mass is now a figure you want. Drying in the sun Let the new sculpture. Now paint your figure. After the glue dries Add it diluted with water to shine and protect. Finally paste a piece of cardboard on the bottom to serve as a base.! And stay beautiful! EASY KEY CHAINS
BOM:
Materialess List: 1 hook female, 1 wooden sphere, 1-key chain, 1 ring keychain, acrylics, and brush.
Instructions:
To begin we must make a hole in the field of wood and if that has not already done, this can be done with a drill or a simple nail. This soon passed to paint the area with the design that we like, whether for a man you can copy the design of a ball or if it is for a woman can make a design more feminine. When paint is dry, screw the female hook with chain, taking into account tighten so as not to leave anything and our work will be soon. It is a very simple, as is done in simple steps, fast, without spending too much, and you can give away or leave for personal use. Also, if you are an expert in wood carving you can play with the decorations or shapes
Dreamcatcher
BOM:
metal ring, ribbon, feathers color, background color, contact cement (clay optional).
Instructions:
Glue one end of fabric to the metal ring and cover them. Colors of thread tied one end to the hoop and make a drawing as a star or something abstract each time you come to an end ring circles the ring with thread and apply a little glue. With colored thread three pieces attached to one end of the ring leaving a party and hang the tie hangs k feathers (3) to each piece of thread and if you want to put a ball of clay
HOURGLASS
Materials List:
2 plastic bottles equal, 1 bottle cap, sand (as needed) packing tape, piece of cardboard, pencil, scissors and a stopwatch.
Instructions: Cut the two
bottle, leaving 20cm long, from the mouth of the bottle (this is the part that is used.) Take the lid and poke a hole in the center, screw on the spout of a bottle. To close the bottle cut the top and bottom, put on the board, make 2 times the contour bottle and cut. The cardboard cut, pasted on the side of the bottle they were cut. Overlapping peaks of the bottles, then put the sand inside. Calculate the desired time, and once managed to hit the tops of the bottles. Done, you have your watch Sandy
AVION
BOM:
A wooden clothespin, cardboard, paint colors, a brush and glue.
Instructions:
Disarm the clothespin of wood and painted white. Copy and cut out cardboard aircraft parts, namely the wings and tail. Decorate the pieces with brightly colored bands. Glue the wings to the clip. Now paint the details of the plane and, finally, glue the tail. 0 COMMENTS
DINOSAURS
BOM:
2 balloons (one large and one small), tempera, glue, water, newspaper or toilet paper, movable eyes and mouth.
Instructions:
Inflate two balloons, stick them together and they are like a dinosaur's body. Lowering the tail in a bowl, and hit the body, two or three layers of newspaper. Allow to dry 2 or 3 days and when you feel that this hard paint it the color you like, let dry and glue the wiggle eyes and the mouth. MOSAIC
0 COMMENTS
BOM:
White cardboard, egg shells, pencil, tempera and paper towels.
Directions: Take
some egg shells, wash and cut them into pieces. Prepare three glasses with tempera diluted in water, need colors: green, red and violet. Now pick up the pieces of egg shells and leave for 2 hours diluted tempera vessels. When the shells have the desired color, put them to dry on kitchen paper. Now draw a white sheet on a picture to your mosaic. Finally paste bits of shell on the drawing
0 COMMENTS
CANS RECYCLED MATERIALS LIST:
1 can (size optional) corospun (color optional), glue / cement or silicone Africa, scissors, sequins, ribbon picot.
Instructions: Wash
tin, remove any label so that the surface is smooth. With the help of a short opener the top of the can. Take measure of the size of the can and cut the corospun the chosen color. Lining the whole can, stick with glue / cement or silicone African cold or warm. Garnish with flowers made corospun, sequins and ribbon around the edges. 0 COMMENTS
BUTTERFLY
List of Materials: Mass
flexible, paste, cream nivea, brush tip finite, ESTEC, transparent plastic bags, paint or food coloring to the cold.
Directions: Take
flexible pieces of dough and paint in desired colors. Save the masses of single colors in bags. Then you have the forms as they appear in the image using the modeling tool let them dry for 5 or 10 minutes. Glue to glue each piece is separate points when you can paint your armed wing and eyes missing. I hope you will luck if you know some things please contact me. 1 COMMENTS
COMETA
BOM:
Two rods of equal length, thread, tissue paper, glue and glue.
Instructions:
started to cut the two rods to the same length using a knife to prevent chipping. Put them in a cross as seen in the figure and tie a knot in the middle. Tie the yarn to one arm of the cross-moving it further away than half of it. Take a piece of string and tie the other arm, leaving the same distance from the center than at the previous step. And tying the other end of the first thread, so that by stretching to form an isosceles triangle. We take the tissue paper and cut a diamond so the surface of the paper tape the rods when placed on top of this pour a little glue along the rods and hook them on tissue paper. We take another piece of tissue paper and cut strips to make the tail longer than twice the diamond paper. Attach the strips to the bottom of the kite with glue. Now is the time to make it fly: That a friend hold the kite in a vertical position and a hold the line at a distance of 5 meters. He who has the thread start to run and the other before feeling the pull of the kite string to loosen up. In this way our comet streak across the sky. Releasing more high fly thread. It is important to make it fly in clear areas away from power lines or trees and on sunny days and a little windy.
. 0 COMMENTS
DECORATING
TOILETS
BOM:
Goma eva, lace or lace, organza ribbon, hot glue, elastic, pinturitas textiles, rubber molds dolls eva.
Instructions: Remove
mold shape and size of the toilet seat. Then glue the lace around the mold. Garnish with dolls eva rubber painted once decorated the lid, put an elastic in the back to ensure the EVA with the lid. And ready
0 COMMENTS
ANGELS FLY BOM: Mass
flexible, ESTEC, sticks, paintings or cold food coloring, glue, clear plastic, cream or cream nivea finite tip brush and acrylic paints.
Instructions: Tint
mass pedasitos the desired colors. You paint with your hands. Dale mass and wing shape in the picture, you let them dry parts separated by 5 or 10 minutes until you see more durito age or younger. And then stick with glue. Luck, hope you like and do not ultilices ahh tempera. 0 COMMENTS
TEXAS RAISED
Yes, but not enough, these homes are not real! They are tiny, and so can you make them. Manuela Rubio Ortiz shared with us these beautiful creations made with tiles. There are very decorative and will teach you to do next.
Materials:
clay tile clay
oils acrylics and glue
ceramic paint brushes
alkyl
mesh
Instructions: Paint the tile
with acrylic paint, white or color that we want to give the fabric. Go cut pieces of clay to form the doors, windows, etc..
must also make the roof Tejitas one to one have to go pasting each piece with glue, and once dry, painted with oils or acrylics. For balconies, we can use wire mesh, removing the horizontal rods, or small sticks made from clay.
We use cold porcelain paste to make small flowers, as you can see in the photographs. 0 COMMENTS
MEDIA TEMPLATES
Now we're in the cold, it's beautiful when we can be at home in warm, but those socks are dirty, then what are we doing today to keep that pleasure is to place templates stockings and somehow turn them into slippers.
Materials: Thick socks
-
-Carton-Pencil-Scissors
-Iron-Fabric-Suede adhesive
Step by step:
started taking socks and putting on our toes or feet of those who will use these measures and support both feet on the board and the pencil mark the shape of each foot. We cut cardboard with scissors, and we took the averages. We
pencil and traced the average size of the cardboard to the suede and fabric adhesive that can join two fabrics. Cut fabrics and then placed in cardboard templates of the middle and place the adhesive material between the cloth and the middle and began to iron the cloth there to adhere well to the media. To end we remove the cardboard and socks and slippers have these original lists. 0 COMMENTS
IGUANA KEYCHAIN \u200b\u200b
Materials: 60cm
wire beads of various colors
Instructions:
Thread a bead to the center of the wire. Insert the wire from the other end through the beads and adjust well.
Repeat the procedure until six rows of beads (put the number of beads as in photo).
LEGS:
Upon reaching the sixth row six threading beads on one end. Bend the wire into the body of the lizard form a loop and pass it through the first three beads. While pulling the wire.
Repeat the procedure but with the other end to make the other leg. Make four rows
threading the moatacillas following the basic technique. Make the back legs with the procedure explained in the previous step.
TERMINATION:
Complete the body of the lizard. To complete re-wires pass through the last bead and cut. 0 COMMENTS
SCISSORS COVER
If you have children at home, things sharp should not be available to them, right? Therefore, to avoid an accident, today we tell you how to make a simple case of felt to safely store your scissors. I have found on Craftzine and not only care for your children, but will be really nice.
Materials: Felt
Scissors Yarn needle embroidery
Step by step:
What you have to do is very simple, put on the felt the scissors, a pencil mark the outline of it, adding about 2 cm all round. With this short form two pieces of felt the same. On one of them overboard as you like.
When you simply list place it on another piece of felt and embroidery thread both pieces together with embroidery. Be sure to leave the top open and ready. Cushions
teaching materials: different fabric colors
Lenci cloth cuttings:
Velcro,
buttons, ribbons, etc..
Procedure: Cut the fabric
in the form of geometric shapes (triangles, squares, circles) the size you want. Join
the two triangles, sew, fill with foam or fleece
Apply with pieces of fabric or cloth such details, doors, windows, fireplace, etc and this will be made a little house. Make
same with the other pillows have different shapes, transform into animal faces, objects, etc.
A fun option is for example let the windows will have on one side and place a piece of velcro with a figurine of cloth, such as a baby, so the kids can come off and apply it elsewhere, or play open and closed, is and is not for children.
With these cushions that can be used for story time, we can work classification of shapes, colors, sizes, etc..
In the smaller rooms can add ribbons, bells some very firm, and all that occurs to us that the child may be playing as well as different textures of fabrics and colors. We can make these cushions
geometric cuts of fabric that we have been previous craft.
Another option is to cushion the center of a hole, of course with all sewn edges, that is more practical to store them in the room.
construct a weighted base that can be a water container filled with sand to decorate at home and we added a PVC pipe painted and decorated, then save when we introduce them into the hole of the cushion, and we all will be well arranged in a corner of the room.
Crafts:
http://www.educacioninicial.com/ei/areas/plastica/tecnicas/simplesycombinadas/index.asp
Chinese embroidery, Chinese or better ....
MY LAST JOB
CARACOL TILDA
GATITA COAT AND HEARTS
TILDA
RABBITS RAT THREE Pressman and El Raton Perez
HANDBAG COLLECTION TILDA
Sheep
felt a snap
NEW WORK
SEWING AND BEAR SET OF FRAMED
a sight that I never tire
STEP BY STEP FRAME MALM
MATERIALS :
Malma Mirror, napkin
CASA Store - fine sandpaper masking tape.
-foam roller.
flat-brush-
Bruguer Universal Primer.
-flat brush - Sponge-Crackle
Praguer step. Acrylic paint Artistik
-Tapioca.
- Lead adhesive. American Satin-Varnish
Step 1: lightly sand it and pass under a cloth to remove dust, cover the glass to protect it.
Step 2: With the roll primer to give all the framework I have given two hands and let it dry well between coats smooth and remove sanding dust.
Step 3: O nce the primer dry sandpaper and tape delimited pintor.Procedemos painted with silver paint roller, once dry, sand it lightly and remove dust.
Step 4: Using your fingers and apply generously making circles Crazing of a country trying not to step ar twice for the same site.
Step 5: Let dry thoroughly and apply with sponge well loaded with acrylic paint and gently pat Tapioca taking care not to run twice for the same site to avoid bringing craquelador.Enseguida see how it starts to crack.
Step 6: Once dry, carefully remove the masking tape and proceed to make a napkin on the framework, we cut and separate the two layers and we are left only with the drawing, place over the frame and proceed to apply with the flat brush and carefully satin varnish, we have to do it very slowly and gradually to avoid tearing the napkin.
Step 7: Once a dry session and give another 3 coats of varnish this time for the entire frame
Step 8: Since we only cut the lead sticker and place it in the frame. MIRROR
MALM "INSPIRATION"
This past weekend we had been virtually a craft forum, was to decorate a frame, we have used most of Ikea MALM mirror for this purpose. Thank you
to Flopy has been proposed by this work, has many ideas and is always teaching us new techniques and styles.
This is the work that I have, I have called "Inspiration" is my first cracked and the first time I use a napkin, before I used thicker paper.
PAPER TRAY DECORATED WITH RICE
This tray is made of rice paper printed a very simple technique which gives us many chances because sometimes as I do not find napkins or paper that you like.
Just select the image you want, cut the rice paper the same as the A4 sheet, put a paper sheet of rice under the subject with zeal for the role of top and bottom, you put it the printer to print on rice paper. Eye
rice paper has two sides a rougher and a more glossy print on your face more satinada.Luego let the ink dry, I stop one day to another and now we only stick to the support we want in my case a tray. TUTORIAL
This FELT pincushion pincushion.
Materials you need:
- A piece of green felt, 30 x 28 cm.
- A piece of brown felt 10 x 10 cm.
- Chunks of white felt, orange (for the bee), and pink flowers.
- A strip of cloth in green 10 x 25 cm.
- sewing thread in color of green felt.
- Hilo thick brown and black
- festoon wires to point
- Plastic or thick cardboard backing to reinforce the bottom of the pin cushion, a piece of 9 x 9 cm.
- synthetic fiber fill.
- fine wire for the antennas (but also worth a couple of pins).
PREPARATION: Cut
the following pieces of green felt:
- 7 x 13 cm. .... A
- 7 x 18 cm ...... B
- 7 x 26 cm ...... D
- 7 x 30 cm .... E
of the printed fabric, cut a piece of 7 x 23 cm .... C
These measures already included the seam allowance of 0.7 cm. Cut
also all other patterns in their webs.
starting work.
1. Fold the strips of felt and fabric (A, B, C, D, E) in half and sewing machine. So we made tubes to which we must turn them over to the right and fill with synthetic fiber.
2. We closed the pipes, connecting the two ends, forming circles. Sew with a thread color felt like to not see a lot of stitches.
3. Once you have closed all the circles, we must unite. For this we will use the brown wire thick and strong. Vale the thread mill but using 3 strands to make it stronger. We started on the biggest roll, which We closed the brown wire leaving a gap of about 2.5 cm. between each turn.
4. When finished the turn, place the circle D and continue rolling over the brown wire, but from now on, we stuck with the needles in the circle E (bottom), each time we take a ride with the brown wire , to be joining the two circles. Continue the same with all circles to build the honeycomb.
5. Flip the comb and fill it with synthetic fiber. Place the circle of plastic or cardboard or, if you choose interfacing thick paste to the brown felt circle is the bottom of the honeycomb. Attaching it to the hive.
6. To close the hole above the nest, Cortal a circle of 5cm. in diameter at the green felt. Pass a basting over the edge, and curl, filling it with a bit of synthetic fiber. Secure. Put the ball in the hole.
7. Now is the time of the bee and the flower. For the bee, cojemos the body, we rizamos basting and putting synthetic fiber inside and closed the thread securing the seam well. With the black, we wrapping around the body of the bee, forming streaks. We, under the body, wings and give some points to secure. The antennas can make them in two ways: by passing a thin wire through the head and shaping, or by putting two pins and thus also be used to fix the honeycomb.
8. For the flower, you put the circle of fabric in the center and fixed with a scallop point. Then the fixed side of the honeycomb.
and you're done, then I'd love to receive pictures of your pincushion. I have put these colors, but you can change them, and do as you like. CHRISTMAS
baby blanket Practice Written by Florence Parma
both winter and summer, if you have a baby, it's important to keep it sheltered at. No need for a blanket ultra hot with a lighter'll feel good, so, this time we tell you how to make a blanket very simple but very useful.
Materials:
printed fabrics for top and bottom sides
Tela
tables Wadding contour
Scissors Sewing Machine
Step by step: Start by cutting
3 equal rectangles, two on a patterned fabrics and wadding. The size of these depends on how big you want the blanket. Once you have located a cut above the other, with the batting in the middle. Make sure that the rights of HACA are printed fabrics outside. Pinned.
With the sewing machine stitching done before you can dial straight chalk, about 10 cm apart. Apart
cut a strip of plaid as long as possible and that should give all around the blanket and about 6 cm wide. Fold first half the whole length and iron it to dial the fold. Then fold each side, provided over 1 cm inward.
The only thing left is to sew the ribbon around the edge. To do this simply place the piece "inside" the tape and you make a stitch.
patchwork blanket with Parma Florence
Writer Just when we are entering spring happens to us we do not know if sleeping with a thick padding that will give us heat or with a thin blanket that can give us cold. It's one of those great questions that probably more than you should have gotten a dream.
To avoid this issue we tell you how to make a double blanket patchwork technique.
Materials: various fabrics
Sewing machine prints
Scissors Step by step:
The first thing to do is cut squares of equal size in different fabrics. Bring them together to form strips of 4 squares long. Form 6 strips of 4 squares long. The size of each table will depend on how big you want the blanket.
Once you have the 6 strips, join them by three lengths. Form two covers 4 × 3 square, and once you have the two faces of the rights of fabrics, sewing the edge leaving an opening. By opening the blanket turns simple straight stitch sewing all around to tidy up.
Way is the sewing machine, I bring a simple craft to get used to using the machine and see it is not so complicated. This is a fleece blanket, very nice and easy. In this case the ideal is for a child is size, but that is up to you.
Materials: pink fleece
1.50mx 1.50m
tubular knitted fabric Morley type of 1m diameter x 50 cm Fabric scraps composé
pink hearts
Interfacing applications
Sewing Machine Needle and thread Iron
Cortes :
polar Cloth: A 1.50m X 1m rectangle (with rounded corners)
knit: 5 x 1m strips 7.5cm long
Steps:
1. Join the knit fabric strips to form the edge. Baste (without stretching the tissue) to 1.5 cm from the edge of the polar rectangle.
2. Skip to machine (without stretching the knit piece) with stitch length, and thread pitch.
3. Turn the edge to the back of the blanket, hemmed in, baste and press.
4. Handmade hidden stitch, sew the fabric edge point on the back of the blanket.
5. Interfacing the remnants of fabric, mark the hearts with different templates and trim.
6. Place the hearts on the blanket interlining, baste and stick with glue stick.
7. Pass a wide zigzag around each heart and iron on the reverse of the blanket.
Tip: Keep in mind that there is extra fabric you can make small cushions in tune with the blanket. A fun rug
Written by Florence Parma
Anything colorful and smooth draw the attention of little kids, and this simple blanket insurance will love. With a lot of pieces of fabric can make a nice blanket for your little ones. It is a very simple and quick.
Materials: Scraps of patterned fabrics
Soft fabric pink pink bias tape sewing machine
Scissors Step by step:
The first thing you do is cut equal squares with different fabrics you have printed. Once you start you cut them together across the width and length. The simplest would be to create strips and then joined the width.
Once you have the squares together you cut the fabric the same size pink blanket which they form. Faces both his backhand and textiles sewn all around to hold. Ultimately what remains is to sew the bias tape all around to tidy up.
If you want to prevent the passage of the tape have to face both fabrics for their rights and sew all around leaving an opening for turning. Turn the piece and sewn all around with a simple stitch fabric
Vinyl Coasters Written by Florence Parma
All we know that our home care must begin with the smallest things. The coasters can be something insignificant, but the fact is that, while adding style, help to protect your furniture brands of glasses and bottles. They are very simple to do and now we tell you how to make a vinyl fabric.
Materials: vinyl fabric
clear contact paper Scissors Felt
sewing machine zigzag scissors cut
Step by step:
The first thing you do is cut square in vinyl fabric and clear contact paper the same size. The measures are of your choice. Glue the front of each square of a square of cloth rubbing gently to contact no air bubbles. Cut squares apart
felt the same size as the previous. Locate each square of felt with the other, on the wrong side. Pinned.
A machine performs a straight stitch around the edge to hold the two squares together.
Finally, matching the edges of each piece with the zig zag cutting scissors to give a nicer finish and neat. Sophisticated
tile coasters
Written by Florence Parma
Whether it is to care for your furniture or just for decoration, coasters are always a good item to take home. But the best part is you do not have to put on spending. If your home has been remodeled and I have left some tiles today and we will turn them into elegant and beautiful coasters.
Materials: small ceramic tiles
the color you want
Medium (decoupage liquid)
Brush Felt
Paper Scissors Glue decorative
Step by step:
Start by cutting a piece of paper slightly smaller than your tile. Apply medium behind the paper and glue on the tile. Be sure to apply enough medium to adhere the paper well, especially the ends. Then apply a coat of medium on paper and let dry. Apply two coats allowing to dry over medium between them.
A Once paper is dry on the tile cut a square of felt the same size as the tile and glue under the tiles. Once it has dried you are ready the coaster. Make coasters
5 more for a full game. How to make a picture
embossed linoleum engraving
The pictures are very decorative elements that are in our home. In shops we can find various designs, sizes and shapes. However, we can also perform them ourselves. Using just a little patience and imagination, we can make a fun, entertaining and practical.
In this report we encourage you to make a linoleum engraving, soft material that works with gouges in various ways in which a drawing. Is to remove part of the sheet material to obtain the relief pattern and, once the sheet of linoleum, apply a paper they exert pressure so that the picture we have at the plate so we can transfer to the paper, ie, obtain a trace of iron that worked. We must not forget that to get the need to wet the paper embossed previously, place it on the linoleum plate and pressure through an etching press.
Click on the photo you want to enlarge
Once we have the picture transferred to the paper, we begin the process. To paint with oil on paper, we give a thin coat of primer on it to prevent oil absorption occurs very quickly, and avoid that greases leave any stain.
Click on the photo you want to enlarge
To make a frame will be equipped with wood in natural state, ie, wood that are not treated in any way. They use them to the back, which will support the print. In addition, the wood should be flat and have four or five inches more width than the engraving.
Soleto
By Silvia Morales
Thanks to Bethlehem
Materials for
Serigraph Materials The starting materials are few, namely
A table (can be the same that is printed and reveals). You will need to have light underneath.
course frame (best aluminum is not affected by anything) and the corresponding fabric (what we call "canvas" is actually a kind of silk that is not altered by any solvent.)
A special knife (type pvc / nylon) for printing is not attacked or damaged by solvents (which are with very strong). These are made of plastic but not a common plastic. They are flexible and keep the edges of their long edges.
a metal spatula (very flexible and finely finished) to expand the emulsion on the web.
NOTE: For the time will be buying spatulas (metal and plastic) different widths for each job. Serves today to begin a 20 cm wide. Presumably, the first jobs will be stickers for cars and decorative and not exceed 20 cm in length or width.
fluorescent light tubes or bulbs (for film. Beware the heat !!!).
emulsion. (There is one for each painting. Example to print the synthetic emulsion is not the same as that used for acrylics. The acrylic inks are for material, they are more flexible on the flags and T-shirts for example. These inks are water soluble therefore emulsion is not water soluble after drying. In fabric inks are 2 types: "A furnace needs to dry and heat in addition to dry the ink creates a fantastic relief where the design (very fashionable in the 90's and before). The other ink does not require anything more than good weather.
A pair of detachable hinges (do not forget to be able to make the frame of the desk for washing). Paintings
print.
Opacol. Mate liquid usually water soluble, pore-correcting-errors in the original drawings (overhead). You can also correct red designs with tempera or other, type ink. Accelerators for dry
inks when wet. (Worst enemy)
retardants that ink does not dry out too quickly (the dry weather causes the ink to dry and clog the fabric).
solvents to clean the fabric of the inks after printing. The final is to wash everything with soap and water. Space
work place while drying (see drawing). There, you just need to test. Do it before offering their services. Should take the time just revealed. Washing. A pressure of the spatula to be exercised over the fabric so that the paint passes. Must learn to recognize the errors in the design on paper to correct them before making the final array to avoid wasting time and money.
is quite simple. The whole process is to move a painting of a specific density, through a mesh (fabric specifically for this task) or can be a paper draft. Notice the steps
--- A very fabric taut over a wooden or metal is the filter support and the design is stamped ink passing through gaps in the design made of some material.
--- The first decision is to know the degree of wire (cm2 or inches) that should be the fabric in its plot.
wire density will make details of the design is possible or not. It also affects the drying and the film will leave on support to be printed.
--- The density of the material used (typically 90, 100, 120, etc) will be adequate for the size and design details. If it contains many details and it's small (eg 15 x 7 cm and lines, very small details or points) we will select a fine woven fabric (type 100, 110.120). To print in large and small with few details of the type used hatched 90. We suggest you buy this at first (90) which is suitable for most of their requirements at the beginning. Step 1
descended on the support frame to print.
We pour a little paint on the end of the frame as far
possible to the picture if you can not close too the edge of the frame. ------------------------------------
Step 2
The drag knife painting on canvas, only going to stand in the place where the emulsion is. That is the design that we previously recorded
------------------------------------ Step 3 and 4
The spatula "travels" from front to back. (In the GRAFCAN assumes you. Is to the left). After the last of the spatula carefully lift the frame and then to see / observe that the support is in place (on the table and not adhered to the fabric) will be back forward over and put the ink the new object to print after removing the form. SUMMING
:
A special fabric placed on a frame is impregnated with a light-sensitive emulsion which does not allow passage of the paintings. Once the paint goes THROUGH the fabric where there will be stamped with the design emulsion
Print Print mirror mirror / reverse image printed below corresponds even reversed because the use will be to adhere to the car window inland. The colors are red, blue and white colors are bound to look more alive and in case you have steak (edge) greatly improve the visibility at all times, with light and dark. For Of course, PVC is transparent. Down
seen the same adhesive as if behind glass
Note: This work was done entirely by hand, without help from pc in 1984 were as rare as expensive and unpopular and had much less laser printers domestic use. So some letters are made of Letraset and other hand and white is totally handmade and "pulse" with China ink, nib or rapidograph (pens). Continue ...
-------- ------ end note
Step 2. Printing:
on PVC transparent and remove the protective paper from the adhesive side we stamp colors first (As stated above in reverse as seen in the picture).
First is red or blue (does not matter because they are stuck) --- note ---
To save time and materials can make in the same fabric both colors. Once the material has appeared in the emulsion should just cover with paper and tape the color that we do not want to use. For example we plugged the red and blue print. Then wash the cloth and proceed to stamp the red while the blue text is covered with paper and tape or directly with emulsion. This does not save time, emulsion, wait and work without text wrapping. We only do two (2) revealed the colors and white. --- End note
.--- Patterned after the colors (red and blue), we expect dry and affixed the overall target will be a nearly full. Below the sticker
ended on a gray table, if in a glass would be the other side.
only remains to say that if anything can be done by hand (the original) and now the pc either a laser printer allows a more detailed and tight.
The final definition, ie the lines and look more perfect details of the plot depends on the fabric. Usually, in too many important details work without using a screening 90 to call him TT (All Terrain). If we want to make fine lines look perfect we will use a dithering 100 0120. (The higher the number of the frame, it will be closer and therefore more loyal details)-Note-also somewhat more complicated than developing.
Light "set" beneath the original.
superior Scheme - Location of the lights for the developing of the matrix. - Note that in both cases there is a black cardboard that prevents light from any source received indirectly over the emulsified material. Performance: The original (blue) allows light to pass in those parts where there are "black spot" of the design. The light "burn / fixed" the emulsion on the fabric (orange). The black cardboard over the orange is for the outside light does not activate the emulsion should not receive light.
frame can be aluminum = (best) or hardwood. = Light source can be incandescent light (there are special for this purpose) or type fluorescent tube. Also sunlight (the best). Paper / Cardboard or paper Cato black = black, completely opaque. Seda emulsion = The fabric that carries the photographic emulsion is particularly suitable tissue type solvents must learn to resist the waiting time for fixing the design onto the fabric. (If the light is solar-sun-it only takes one minute or two, depending on the sensitivity the emulsion).
Lattice
When we decompose a picture (Or design) for a process color (4-color print) to get all the color tones are broken down into dots of different sizes and density. This is cross-linked. When an image lattice, the points leave empty spaces in the printing of a color that will be filled with the next color achieved from both a different color.
For example, suppose that you print yellow and red in their work. If the first red and yellow prints get an orange top (for transparency, because it does not cover the yellow to red), more or less desirable. But if grid of red and yellow will get the orange you want or at least a stronger tone than that produced by the previous system.
What is the grid? The grid is "the" indispensable support for printing with minimal number of colors but that seems to have more. Below is a normal image and the same lattice below. Top left
- Black and White
The above image from black to white screen is almost impossible because you can only make one pass at a time. But if "grid image (black and white image below). The black dots becomes increasingly separated and thus "appears" to be increasingly gray light to reach the target. In the image exaggerate the point size to make it look as clear as possible and note the passage from black to white. Mindful that in the demo the lattice is expanded so that you can. appreciate it. In the left image
color gradient from red to yellow, we see that the red dots will appear separately until they are gone. The effect is the same. When you want to print a process color (4 color, real color, such as a photo) should proceed as it does a printing press. The image must be decomposed into 4 colors crosslinked (CMYK) that are mounting all the original color. At
photo / CMYK it is best to pay for the work contacts (slides) but if you know (enough) design software and the printer has the ability to make small enough points (more than 600dpi) ( usually are printers who understand the Postscript language) can do at home. The ability to print the printer is very important, the second is to master the program design for color separation. The images
always the same as a filter has been applied to the grid and are ready to make contact. This section aims to help to solve the classic and nice "gradient" that can be inside of letters and funds as reasons and background of the overall design.
At first this will complicate life, but before long you'll want to do spectacular things or at least remarkable quality and then this system apart from the change.
something important: When using the reticulated appearance of the work is that more than one color on the form. The show greater gray (single color, which becomes black points that are separated). You can do shadow effects and volume without adding other colors.
A good example of what is and what is CMYK color separation, load a picture in your image editing program (eg Photoshop) and locate the command will be separated into CMYK and the image is split into 4 images black and white. Each image of these corresponds to a color (the name is in the window frame of each image). If you look closely you will see for example that if the photo had a lot of red full or nearly corresponding to the Magenta will be sharper and full as those that are composed of various shades (eg green forms of Cyan and Yellow).
Another example to observe on the lattice. Take a magnifying glass and see in detail a magazine or a newspaper printed in color. You will see that the image is composed of small dots. Die
adhesives often be seen having the form of design, or support is not rectangular or square. This is achieved with the "die."
What is it?
is a piece of metal that is sent to a craftsman or a machine that has the exact outline form will the paper after printing. The die has a cutting edge high end and the other a piece of wood or metal that supports it.
Suppose that the adhesive has the shape of the design on the left .. The adhesive is red and yellow and printed paper is the gray (the paint to get an idea of \u200b\u200bwhich we speak). The gray part is the role (or PVC) cut to shape, in this case, the sun. After
paper or PVC printing proceeds to make and use the punch to take the gray form design (can be as complicated as you want). Normally this cut is on transparent PVC, which, by adhering on glass will not see the adhesive.
Who makes the cut in each adhesive? Well
one can do it by hand one at hand. You can invent a typewriter (not difficult with today's cheap technology) or you can bring prints, stickers, and a printing press where the die will be used in place of the old cliché cliseé.
The die as we said, is a piece of metal in the form stipulated in the design that has a significant edge when striking an edge on the PVC-or paper-cut to the precise and fast.
How to make a good flag with
class A flag is generally used for football clubs, golf, volleyball, schools, squash, etc, etc. Normally it is donated to the club opponent turn. Must be a nice flag, pleasant, attractive, and for the world "Beretta", "ordinary" cheap at first glance. The flag will be displayed in a wall, a window or somewhere important to the club who has been gifted. Many people will see it, so there should be low or poor quality. If this happens, the flag is not just a laughing stock but that will adorn the "doghouse" of the club mascot receptor.Veamos how to make a banner ... quality. Here
influence several details and the hands of at least 2 people and not just the hand of the screen printers.
-
design - the number of colors
- the screenprinter
- a seamstress
- the armed materialesel
- the "shell" or back that will give "body" stiffness.
How to make a good flag with
class flag in the left, we see a satin banner (cloth bright, glossy and very similar to silk usually white but can be achieved in different colors). Let's skip the form which is equal to the description on the site. Never the flag is printed on opaque fabric but if you can be the ink. (Ideally semi-matte / semi-gloss).
The flag of the sample is in the rear a large rice paper that was sewn together with fringe (3) (the satin and tassels are purchased by metro) and printed fabric with ready-made (M).
The yellow border here is just paint, but you can put a string that makes it more rigid, yet. At the top is sewn by folding the paper and the fabric so that we can then place the plastic rod (PVC) or wood that will hold the cord (1).
In this study, go around the flag fringed in general. Can be made cheaper as seen on the left.
Finally we will indicate that: first prints without cutting any of the material, calculating the cut and fold up for carrying the stick and the fringe and if I had a cord is sewn to the latest together with the remaining rice paper hidden under the cloth. The last step is to place the stick and gripped the rope with the pointer "P" which is a plastic that go along with the rope comes under pressure. ready Tip: If you can not do without the flags behind rice paper. If you can not made up banners without fringes (there are ugly, or empty). Remember to take the white cloth that is unsurpassed in the case of the top banner above the letters' Etc Athletic Club "would be the canvas unpainted.
home Improving the System Enhancements
print if you decide it is the job of your life you have several options to improve the work.
The improvements result in more economic benefits, as any resulting improvement in speed, speed is low cost and improved competitiveness. Let's see:
1) is a good idea to have a small room or space dedicated where matrices reveal.
2) There are automated printing tables where the only thing the user does is build and test that everything is fine. If you choose this purchase and can not think 2 times is the best you can buy for your work. It is a metal table that has a vacuum cleaner that still maintains support for printing and also has a movable arm that allows precise and rapid adjustment chablón (frame). There are many advantages of this table that purchase made. do not hesitate, get a loan and buy it, pays for itself!.
3) As you might not have funding to purchase the table above named will try to make it home. A vacuum under the table. (See the design left) be the most important function is to make the adhesive is still on the table and lifted the frame.
E: is the tilt up and down the rack.
C: It is the hinge that allows precise movement always rising and falling with each pass. (Do not move anything, but the next does not match the color above)
A: and B is a vacuum: it is a kind bag of metal, wood or whatever you can think of where you produce the necessary vacuum to suck on through small holes of 1mm or 2mm should have the desk.
As you will cost you money and get a pllancha metal work for the table, suggest that uses a timber of good quality and we realize holes of no more than 1 or 2 mm to allow the cleaner to do its job to aspire to travez the perforations.
What is the point?. It happens that when making the past with the paint for paper or pvc (any) tends to rise with the frame and the paint left him stuck in the bottom of the fabric where it produces the fabric-paint-touch support. There are 2 ways to avoid it,
to: with a little contact cement is achieved by attaching the bracket to the table and
b: with a vacuum under the table which of course will have many holes like tiny needles through which the vacuum attempt the object that is sucking up the table. Beware! the holes of the table must be very small and stuck to each other. Ideally, the table is metal. The vacuum cleaner (that were previously expensive) absorb the air for no trance / stop for the other holes of the table to be free. Should try to avoid overheating the electric motor of the vacuum, remember that most have variable speeds. Nor need much suction power.
P: is the support for printing (paper, paper, fabric Canton, etc).
M: is the table.
D: is the frame.
Other improvements (necessary in a short time) is to be
Improving
Other times and quality improvements (necessary short time) is to be hatched buy different fabrics and their racks. Please note that the fabric of the racks are not replaced until they break. (And even if the break is on the side and not too large can be covered with very sensitizing emulsion which will not move more)
precious time is lost by washing racks and waiting to dry. Imagine having a decal 2 color on white paper and has only one frame. Must make the impression of a color, wash everything, wait to dry and then the emulsion, developing, wait to dry the emulsion, assembling the stand again to just print the second color. 5 hours with good weather, minimum!
fabrics must have frame racks with 80% (for prints fine details and text ideal for full details and designs without too small), 90% (used for the majority of the prints). 100% (for prints with precise details and small), 110% and 120% for prints of photographs.
Another improvement that should have from the beginning is easy to remove and place the rack quickly and easily adjust to the new color that will go on previous form, and (speaking of more than one color).
See designs below. Figure
left profile of the many ways that you can fix the frame. Usually this is about 1 inch thick and if wood is hardwood lapacho type, etc. The frame can be aluminum that is stronger and does not change with the weather or water.
A: is the frame with the fabric (the gray part at the end symbolizes the thickness of the frame).
B: is the hinge of motion on the table. This allows the frame can be aligned to the figure and printed (or transparent original is better). This piece is usually done based on a hinge bought in good quality. Also made and sold are excellent.
T: The butterfly that conforms to frame the movement of the piece. Set the rack so it does not move during the entire duration of the printing (if you move .. !!... lost money and time).
M: is the movement of adjustment.
The blue-painted piece is fixed to the table and the corresponding hinge. Screw Butterfly (T) - which of course has a nut on the other end soldered to the blue piece, pull the frame until it fixed and firm.
not take this example as unique. The only requirement for this piece-key-is that it moves across the print. Note that if you need a run of 100 2-color adhesives need to download and upload this frame 200 times (100 for each color), plus the inevitable tests.
for free
ready to make money coming to this page update your browser or press F5 to refresh to see it again. Added May 2009 Original
garment
We will be adding original print garments, especially jackets in light clothing and light-colored effort to find it easier, but you. can print on any material and any color with the same original. The first installment consists of 2 original (and variations) ready to print to a color or 2 without problems. See more here, including the manufacture of a simple home machine to print 2 colors. Here
has several famous original format ready for print corel draw where you most ineterese. Shirts, T-shirts, sweatshirts, cards, stickers, etc.. Free. Click on the image. Requires an e-mail to receive the password valid. Click
Download free practice files (requires a password to download) Click
Free Download and print logos on clothing, stickers or wherever you like. A night of nostalgia August 24, Punta del Este. Designs
faces of famous musicians to a color original, vectorized ready to climb to where you need without distortion. Click
---------------------------------------------- Top 4 ---------
classic designs easy to install. 2 designs of "toilette" public for adhesives or printing on acrylic or wood for placement in business. Another design language churches all "Peace not war" and the other green design is a popular design for lovers of fishing and hunting. You can change colors as you probably already know if you have read the entire course on this site will continue to add designs
shortly
design & illustrator
Important: The most important section of your company (if facing the project as proposed by and future expansion) is the graphic designer.
Designer (formerly called us designers) must first have experience in the field screen, you did not know you will show in-situ as done. This will provide you with the best time as well ideas, an endless list of shortcuts to save money on printing.
graphic designer as possible should be "creative", will be the one to your taste, the author of "true" success of its sales and design / prints / company.
* In which state is the basis for this item properly?
- just one example, The goodies Chinese / Taiwan / korea / etc (which is good and bad quality), as well as any source of imitation of famous brands, always imitate the creations Italian, German, Swiss, or French. You see the number of objects of imitation that exist. Rolex, Cartier, Gucci, Fiat, etc. The Italians are the kings design and good taste.
* creative graphic designer has in mind the design long before you even visualize it in the preliminary sketches.
* You can be the "Oscar" of the accuracy and thoroughness in completing their projects printed but, if not a good design is useless meticulous and painstaking work.
* The graphic designer, knowing the printing system and past few days working on site (if you do not know the printing system) will save you money by telling you that this or that color should go first to save time and money.
* You can be the "Goya" print but if the designer who makes original (PC or by hand) is sloppy and do not pay extra attention to detail, of no use teamwork (you and him in his own designs). If the original designer who prepares the misses in a millimeter you will lose lots of money on time, testing, inks, solvents, various materials, washed, acetates, etc. Because they simply can not cope with the guidelines so that the colors are, each in his place. What is done will not help, start all over again.
* A good creative graphic designer appreciates the opportunity that you give and you should educate them not to spend hours reviewing original. It is true that you should review for anything, but one thing is routine checkup and another is "knowing that something almost certainly will be fine." Design errors and time is money you lose
ideas can, "to make some start-color stickers to a type 20 cm by 7 cm. (Economic) to a color (remember the white paper.) So take advantage of the background color pvc
See the example on the left. There is only one color but it seems like 2. The black lines are separated and seem to form a gray. In this very basic design and rushed the lines are separated with too sharply if more care would be better the effect. If instead of red and black out the bottom of the paper, yellow would a sunset with only one color. Try and see.
The subject may be "green," campaign against drugs "," clearing the city, "" messages of social justice "," your own sticker promotion "," logo of social sites or property, or tourist "There are a thousand topics, consider.
How to sell your product? Think first
who was going to sell. Such a sticker on a beach is visited especially by young people, must bear a color and "mambo" fashion. Remember the sticker that said "Bad Boy"?, Was famous and was silly. Think
also (if it is a social issue) that can offer at bus stops and traffic lights, to passersby, "will", meaning that you give what you can. It is highly likely to receive more money than if you put a price. That issue itself should be of interest to all and a lot. Each sticker will cost you no more than 2 dollars and receive no less than $ 5, almost certainly. The other idea is to use foreign names famous beaches. Cholula never miss the purchase.
Be careful if you copy something. Best
not copy, brainstorm on ideas of others is better. Often what stands out is a combination of colors or distribution and not the model or design.
not a good idea to copy and do not say the problem only by law but once you get used to copy your neurons and no longer work. Look success is always on the original side of copying or imitation.
closing, there is nothing you can not do with this printing system, with the exception of "stamping" that makes it a Clisse.
What is it and where you use the stamping? It is mainly in the front of the agendas (expensive) leather, and are those that have letters on the front very bright gold color is gold paint. A metal stencil design, hit the leather (that's why you always see in low relief design) on a thin film blends of bronze and gold or copper that makes the characteristic sheen of stamping. So Painting is not gold.
sales and investments ideas for small
Do not think you should only expect the customer, not for nothing, you can make small investments and while recovering the money can grow as your reputation grows and begins to be known.
ADVANTAGES OF THIS OFFICE (almost) ARTISAN
ideas for the beginning, when the clientele is still high. (We look) -
• First to have a small capital to start.
• Purchase of paint (ink) cost is low comparing performance ratio - price. With one liter (or kg) of ink are printed letters miles.
• Set on the principle that try products primeror sell. Assessment eg sales locally and Internet as well as potential resellers in nearby areas.
-> If you live in a cold climate do not buy T-shirts (sweaters) light summer clothes .... . Evident. Consider purchasing light waterproof jackets that can print. Suppose we can afford to buy new clothes at great prices "should not be printed" on the web. Choose light colors, dark are more difficult and requires a white or gray. If you live in warm weather then light wear / light is the choice.
-> If your city has offices, professionals, shop, or business and especially if you are near a provincial capital agendas consider investing in "permanent" (agendas that have no year, just months) of leather, plastic, pens (of hexagonal or square) acrylic keychains, etc, etc. kind "gifts" business (BBB-good-pretty-cheap).
-> discarded that ud.intentará first make adhesives. If so (good idea) look for topics of their city especially if it is a tourist area. If not see the fashions. Eg. as a novelty sport of Wind-Surf everybody had a sticker on your car's theme and some do not even know how to swim in the bathtub. The same with the surviving Surf while almost all parts of the world. Now they are fashionable gliders, wings deltas, (that if there is more support for the problem but eventually prices will drop insurance) mountain bikes (mountain bike), hiking etc.
-> Stickers (stickers) on drugs always work. Flags of the most popular football club and also never die, they just need the expectation of a classic and sold like hotcakes.
-> Adhesives environmentalists and peace (good song)
When printing generic adhesives can agree with NGOs or non-profit association or charity (which are always on the "canvas") and profit sharing. For example they go on sale on behalf of the organization. If for example
you decide to sell what they do, say adhesives of the song "I love my city" (eg I'm love Córdoba). Then you can hire young people without work in the corners where there are traffic lights to "sell" the product. Instead of opting to accept a fixed price "at will." That is priceless. In 80% of the payment exceeds the cost because people generally gives what he believes is true especially if the job is nice.
can be done with serigraphy
What can be done with this system? What I can print with this system? Keychains Keychains
plastic magnetic
Acrylic Keychain (you cut and print, very easy)
Adhesive paper, PVC
electronic circuits
Cards Communion Cards Postcards
special invitations and special openings on glossy cardboard Brochure
large fine.
packing boxes or large objects
boys clothing (shirts, shirts, jackets, caps, etc)
Calendars on cardboard and cardboard posters
PVC-plast (PVC hollow)
Pennants, Flags & Leather Agendas / or fabric / imitation embossed printing
Ceramic Trophies Custom printed paper bags
and / or cardboard, plastic bags
Flyers Printing directly on objects / appliances
Tags
metal mosaics decorate
Wood (objects and furniture) Serigraph
electronic parts are handmade or mass produced.
Cartons (boxes are printed unarmed).
Anything you can think
- The banners are printed before being cut from the final form.
- Flyers like to take and print several at a time. Then cut by hand or in a guillotine.
- Their forms are good or bad, impressive (like factories recognized) and identical to the originals (or appear to be original) will depend on 2 situations / Actions:
a) the design
b) quality and form completion.
If in doubt just see objects made by Chinese children who are kings of piracy of designs and famous and have achieved the highest quality identical to the original .... apparently clear.
several
Title nonsense found on the net "ideal solution to the home screen Effects Pedal is what we call in another page of this site as a" Transfer ". Not worth it unless, that is intended to print a shirt with faces or photos in full color and screen printing is not exactly. Must be printed on white or very light fabrics and the printing is very thinly also is not too strong on the web.
What if the fabric is firm until the day I die garment is the transfer of American origin (USS). They are terrible, full-color transparencies, thick and very flexible and really unsurpassed quality.
Care! the screen "real" as it is explained on this site, everything else falls under other names or devices such as eg. "Offset printing" or "pad" or "transfers" and other names that I can not remember but not more than two posters always talking about business or commercial or artisanal posibildad mass reproduction. Another
"nothingness" is to believe that it is "a work of art or craft" The truth is that "may" be a work of art as long as the artisan has created a work that will be "art" original, innovative, new, etc. But today is called "works of art" forms that were compiled from other famous works (or not), or were copied and changed, we're the standard for most. The truth is that the artwork is one, the original then there is no real masterpiece but copies more or less similar or identical. This actually began when an artist made a lithograph printed by hand by artisans from end to end. Are numbered and sold. The value of the work is greater the less they also printed the first editions are worth more than the latter. But for several years now and this is done by machine. That is the only artist makes an original machine and does all the fine signature. Say what you want, but we are not an original work of art is a copy as do the Chinese.
So many bad calls we craft fairs where they consider a handicraft product of screen when the truth is that who sells and / or produced in 99.99999% of the time have no idea how to make a line with grace and elegance much less a "craftsmanship" and less still "a work of art." That is to belittle, downgrade and denigrate the "true craftsman / painter / sculptor, etc" breaking the fingers (and the "roof") and "think and try create original designs and new. "creations, objects that are usually sold" as low as the need "like a" Chinese chirimbolo more "(we know from experience) that many use to decorate a bathroom, a garage or hallway where not seen anything and you want to hide a stain humedsad.: Glossary
Matrix = is called the "matrix" fabric and emulsified. Ready to "make / print" the original design of the paper.
= emulsion photographic emulsion . It is a liquid (dense and particular color (varies if fabric inks, pvc) applied to the canvas with a special knife to avoid damage in very thin layers.
Inks = Paints used for printing. Original
= You say "original" design on paper.
frame = we tell the framework that holds the fabric. Also called "chablón. This can be aluminum (ideal for light and resistant) or very hard wood. Acrylics
= water soluble paints. Synthetic
= synthetic enamel. Full
(s) = It says "full" to the imrpesión that no details. It is usually the general fund.
Acetate = PVC Type suitable for printing and / or draw with ink. Is very similar to X-ray plates and rolls of film pictures .. X-ray plates can be washed (with bleach) and use it to original as is sufficiently transparent.
Trama / Dither (80, 90, 100, 120, etc) = indicates the distance of the strands forming the weave of the fabric to be used in printing. The higher the percentage of screening material is steeper (and more difficult to print and the final revealed as surely has many small details the original and takes a lot of attention and care.) Dither lower woven fabric makes a more detached and therefore less fine detail.
Lattice = Refers to the decomposition of a color gradient (or degradee) uniform point that similar tones, Lattice
CMYK - Process color - Said of an original that contains the 4 basic colors that form the whole spectrum of colors and tones
0 comments:
Post a Comment